吸附物式干燥處理機

◆產品特色 Product features

※享有安穩高度的吸氣負壓和露點

1.吸附物塔之極度與長度經科學試驗的結果高精度測算，塔床摩擦阻力小，保護了降低有毒氣體烘干劑5秒的排斥時長，滿足需要樣品氣的露點要。

2.30％的變干劑剩余，適用房屋補償變干劑的自然生態銹蝕，確認變干。

3.門頭粘附器，確保空氣勻稱采用烘干劑層，消減溝流物理現象。

※粉碎氣量損失不大于14％

1.匠心的機筒結構設計，留存100％的溶解能量，永久保存的能量于多恢復性能環節的恢復性能氣溫，挺高裝置的解吸性能，不使恢復性能更根除。

2.皮膚干燥和降解按照方向對流傳熱策劃方案，濕氣流流淌干的離心分離劑時效性果最佳。降解氣外貿出口含濕量掌控在亞呈現飽和心態心態，使消音器及排氣口通路無結水之慮。

3.可不同潮濕機的作業阻抗各種需求設定再造氣使用，為了保證再造氣團重復穩定性高，再造壓差低至臨界值。

※空氣干燥劑使用的質保期長

1.恰當的機筒寬度，使氣體在缺水劑層的氣速和耗時保證好的模式，足夠發揮出來缺水劑的機械性能。

2.節省的系統化標準配置，在空氣滲入機筒前，經除油清理盡快清理空氣中內含油量物與重被污染破壞的物，應對干燥的劑層受被污染破壞的。

※系統選用了貼近生活高品控電動三輪及液壓閥和穩定的全光電子可編寫程序序有效控制器接線圖，電腦程序界面和睦，定時累計體現雙塔負荷率，巡環期現場報道可編，原廠確定10min。閥體使用期限有50萬次瑜伽動作。

※筒節開口處作冷鍍鋅管除銹防銹治理，10年不氧化。

※動作精確度、效果可靠、操作的簡單便捷，進行安裝免基礎條件。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆核心高技術數據 Main technical parameters